Franklin-fueling-systems T5 Series Fuel Management System Operators Guide Uživatelský manuál stáhnout pdf (Strana 31)

Appendix B – Alarm Table

Note:  Refer to Safety Instructions outlined in this manual prior to performing any maintenance on or inside the console.

Note:  If at any time while troubleshooting a Warning or Alarm this guide does not correct the issue, contact FFS Technical 

Services.

Warning

Always remove power from the console prior to installing or removing a module or performing any

maintenance while the console door is open.

System

Displayed Warning Description Recommended Actions Reference Source

2-Wire Sensor Module

Is Ofine

The specied 2-Wire Sensor Module 

listed with the alarm has experienced 

a problem or may not be recognized 

by the Controller Module.

Cycle power to the console. Visually 

verify that the green ‘RUN’ light on the 

applicable 2-Wire Sensor Module is on 

continuously after the system boot is 

complete.

Installation Guide / 

Applicable Bulletins*

2-Wire Sensor Module

Number Mismatch

The number of expected 2-Wire 

Sensor Modules does not equal the 

number of 2-Wire Sensor Modules 

installed.

Verify the physical number of 2-Wire 

Sensor Modules installed and compare 

with the number of 2-Wire Sensor 

‘Modules Expected’ in the programming.

General Setup in

Programming Manual

 / Applicable Bulletins*

3-Wire Sensor Module

is Ofine

The specied 3-Wire Sensor Module 

listed with the alarm has experienced 

a problem or may not be recognized 

by the Controller Module.

Cycle power to the console. Visually 

verify that the green ‘RUN’ light on the 

applicable 3-Wire Sensor Module is on 

continuously after the system boot is 

complete.

Installation Guide / 

Applicable Bulletins*

3-Wire Sensor Module

Number Mismatch

The number of expected 3-Wire 

Sensor Modules does not equal the 

number of 3-Wire Sensor Modules 

installed.

Verify the physical number of 3-Wire 

Sensor Modules installed and compare 

with the number of 3-Wire Sensor 

‘Modules Expected’ in the programming.

General Setup in

Programming Manual

/ Applicable Bulletins*

4-20mA Input Module

Error

Input amperages have exceeded their 

thresholds—this Error applies to the 

4-20mA Input Module listed with the 

alarm.

Troubleshoot external 4-20mA device and 

wiring from the module and channel of the 

4-20mA Input Module listed with the alarm. 

Applicable Equipment 

Guide(s)*

4-20mA Input Module

is Ofine

The specied 4-20mA Input Module 

listed with the alarm has experienced 

a problem or may not be recognized 

by the Controller Module.

Cycle power to the console. Visually 

verify that the green ‘RUN’ light on the 

applicable 4-20mA Input Module is on 

continuously after the system boot is 

complete.

Installation Guide / 

Applicable Bulletins*

4-20mA Input Module

Number Mismatch

The number of expected 4-20mA Input 

Modules does not equal the number of 

4-20mA Input Modules installed.

Verify the physical number of 4-20mA 

Input Modules installed and compare with 

the number of 4-20mA Input ‘Modules 

Expected’ in the programming.

General Setup in

Programming Manual

/ Applicable Bulletins*

AC Input Module

is Ofine

The specied AC Input Module listed 

with the alarm has experienced a 

problem or may not be recognized by 

the Controller Module.

Cycle power to the console. Visually 

verify that the green ‘RUN’ light on 

the applicable AC Input Module is on 

continuously after the system boot is 

complete.

Installation Guide / 

Applicable Bulletins*

AC Input Module

Number Mismatch

The number of expected AC Input 

Modules does not equal the number of 

AC Input Modules installed.

Verify the physical number of AC Input 

Modules installed and compare with the 

number of AC Input ‘Modules Expected’ in 

the programming.

General Setup in

Programming Manual

/ Applicable Bulletins*

IO Input Alarm The input senses either voltage pres-

ent or no voltage. This alarms when 

input voltage is not as programmed

Verify that programming parameters 

meet site specication. Check all wiring 

associated with the input at fault.

Installation Guide / 

Applicable Bulletins*

IO Module Number

Mismatch

The number of expected IO modules 

does not equal the number of IO 

modules installed

Verify the physical number of IO modules 

installed and compare with the number of 

IO modules programmed.

Installation Guide / 

Applicable Bulletins*

* Bulletins and the T5 Series Installation Guide (p/n 000-2150) and the T5 Series Programming Manual (000-2142) can be found on 

Franklin Fueling’s web site - http://www.franklinfueling.com/service/.   Select Technical Documentation / Fuel Management Systems

1 2 ... 26 27 28 29 30 31 32 33 34 35 36 ... 45 46

Komentáře k této Příručce

Žádné komentáře

Franklin-fueling-systems T5 Series Fuel Management System Operators Guide Uživatelský manuál Strana 31

Komentáře k této Příručce

Související produkty a manuály pro Zařízení Franklin-fueling-systems T5 Series Fuel Management System Operators Guide